Description
Description
The Toyostove Laser 300 is the smallest output wall furnace available from Toyotomi. The Toyostove Laser 300 heats up to 720 Sq. Ft. of living space for at a fraction of alternative heat sources. The Toyostove Laser 300 is a sealed combustion or direct-vent system that uses only outside air. It also vents gases directly outside. This Toyostove high-efficiency model provides safe, comfortable warmth for zone heating, small homes and cabins.
Features
Features
EFFICIENT AND ECONOMICAL
Toyotomi Laser products are the most fuel-efficient, energy saving, oil* heating systems available.
- Uses up to 50% less fuel for heating comparable size areas than conventional oil-fired heating systems at a fraction of the cost
- Pays for itself in fuel savings in just a few short years
- Special stainless steel heat exchanger insures the highest efficiency rate
COMFORTABLE
The Lasers series large circulation fan distributes heat quickly and evenly in order to maintain and optimize maximum comfort.
- Automatically regulate between low, medium and high temperature settings
- Self shut-off when room rises approximately 4° above the desired temperature
CLEAN, SAFE & ODORLESS
Advanced heating pipe-within-a-pipe forced flue venting system creates smokeless, odorless, clean heating.
- Lower emissions (up to 50% less CO2) than conventional oil-fired heating systems
- Outside pipe brings in outside air for combustion
- Inside pipe exhausts all combustion by-products to the outside
- Circulating fan distributes heat
- Cool-to-the-touch cabinet safe for kids and pets
- Permanent mesh filter protects circulation fan and interior components from dust
- Electric surge protector and shut-off safety system
FLEXIBLE FUEL OPTIONS
Toyostove Vented Heaters can use the following fuels without any modifications to the unit:
- Ultra Low Sulfur Heating Oil (ULSHO)
- Ultra Low Sulfur Diesel (ULSD)
- #1 Low Sulfur Fuel Oil, or K-1 Kerosene
EASY INSTALLATION
Owner's manual provides complete, step-by-step instructions that are helpful and easy to understand.
- Installation takes about three hours, or less
- Vents through a side wall using the direct vent kit which is included with heater
- Full range of optional parts and accessories available offers a variety of different installations
Specifications
Specifications
Fuel Type: | ASTM D3699 K1 KEROSENE ASTM D396 NO.1 LOW SULFUR FUEL OIL ASTM D975 ULTRA LOW SULFUR HEATING OIL/ DIESEL |
Heating Efficiency: | 87% (AFUE Rating) |
Heating Rating: | 15,000 BTU/Hr (High) 10,100 BTU/Hr (Medium) 5,310 BTU/Hr (Low) |
Fuel Consumption: | 0.108 Gal/Hr (High) 0.076 Gal/Hr (Medium) 0.040 Gal/Hr (Low) |
Size (WxHxD): | 17-3/8" x 21-3/4" x 15-1/8" |
Weight: | 31 lbs (empty) |
Heating Area: * | 600 Sq. Ft. at (0°F) 720 Sq. Ft. at (20°F) |
Max. Length of Vent Pipe System: |
Maximum 10 Ft., 3 bends or less |
Electrical Rating: | 120 Volts AC, 60 Hz Preheat: 240 Watts Burning: 23 Wattts |
Vent Hole Pipe: | 2-3/4" - 3" Diameter |
Type of Tank: | Exterior Tank |
* 0° F Heat Load = 24 BTU/ft²/hr
20° F Heat Load = 20 BTU/ft²/hr
Room size for which this heater is suitable will vary depending on outside temperature, house insulation, window
size and other factors.
Literature
Literature
Support
Support
Manuals: Operation and Installation
Owner's Manual Toyostove Laser 300
Support Videos
Trouble Shooting and Maintenance
Cleaning: Flue Pipe Assembly for Models Toyostove Laser 30,56,73,OM22
Cleaning: How to Clean Your Toyostove
Combustion Blower Exhaust Fan Balancing
Commonly Used Parts for Toyostoves and Oil Misers
Error codes for the new Toyotomi product line
Igniter Installation: Using an Ohm Meter to Confirm Proper Installation
Igniter: Removing a Stuck Igniter on Toyostove Laser Heaters
Ignition Sequence for Models Laser 30,56.73, OM22, BS36, OM148
Operating on Toyostove on a Generator
Parts Diagram Toyostove Laser 300 (Type A)
Toyostove vs. Other Stoves/Fuel - Heating Cost Comparison per Therm*